UN210-KIT USRP N200 ETHERNET SERIES AND ACCESSORIES

Own private GSM transmitter just for you...

Designed for commercial deployment for abandoned areas, mining parts, or laboratory simulation of 2.5G networks or simple replacement of GSM site in the event of a commercial network outage.

The Sigint-BTS-900 series acts as a single BTS network for custom GSM phones or as part of a multi-site network. It can be configured to support 7-35 or more current calls and distances of up to 35 km

UmTRX is an SDR transceiver inspired by USRP N series. If you worked with USRP N you will find it familiar, but there are significant differences which are described below as well.

Single board with an integrated RF part.

Optimized for industrial use and high MTBF.

1GbE Ethernet connectivity to a computer.

Two full-duplex RF channels (side "A" and "B" in UHD).

Single chip transceivers LMS6002D are used for AD/DA and RF processing (300MHz to 3.8GHz)

Stable reference clocks:

26MHz TCXO (integer multiple of GSM sample rate) with 100ppb frequency stability.

DAC for TCXO frequency fine tuning.

Integrated GPS module for automatic TCXO frequency stabilization.

External clock source is possible.

Thermal sensors for temperature based calibration.

After having successfully created PandwaRF, we used this expertise to develop a more powerful device for pentesting professionals and Law Enforcement Agencies.

FUNcube Dongle Pro + has the same design objectives as the original FUNcube Dongle, but we have taken into account many comments on the original FCD and have improved both performance and functionality. Although it may look similar from the outside, it's a whole new design.

In terms of performance, we have added 11 discrete hardware filters to the front, including narrow SAW filters on amateur 2m and 70cm bands. This has a hugely beneficial effect on blocking the front-end, especially on the VHF.

There is also a new LNA used with much better performance, which improves OIP3 to 30dBm (around 10dBm). In addition, the rf grades are at 3.15 V compared to the original 1.5 V FCD, which significantly increases the dynamic range.

50 MHz to 2.2 GHz Transceiver. One MCX-Bulkhead cable included, for full duplex order an additional MCX-Bulkhead cable. Note: Not for use with USRP1 serial number 0 to 500.

USRP E100 Kit, includes USRP E100, 2 RF Cables, Power Supply, and Hardware Package.

USRP N210 Kit, includes USRP N210, 2 RF Cables, Ethernet Cable, Power Supply, and Hardware Package.

RTL-SDR Blog R820T2 RTL2832U 1PPM TCXO SMA Software Defined Radio.

The software-defined Radio Starter kit includes a USB hardware flash drive with a widely supported Realtek RTL2832U and R820T chipset and a versatile MCX antenna.

Several improvements to generic brands, including the use of the R820T2 tuner, improved component tolerances, a 1 PPM temperature compensation oscillator (TCXO), an SMA F connector, a circuit with distorted outlet and switch-off plates for easy direct sampling adjustment

FUNcube Dongle Pro+ l, AMSAT-UK FCD2 regulatory statements

Many thanks for purchasing the FUNcube Dongle Pro+! The FUNcube Dongle Pro+ is a software-defined radio (SDR) covering all broadcast and amateur radio bands from 150kHz to 1.9GHz. With an SDR, many of the functions of a traditional hardware-only radio are performed in software, such as demodulation, decoding and frequency conversion.

The Software Defined Radio Starter kit includes a USB dongle featuring the widely supported Realtek RTL2832U and R820T chipsets, plus a versatile MCX antenna.

The SBS-1 receiver is able to receive aerial information about aircraft in your sky in real time. He can identify the plane, its marker, determine the direction of flight or its air height and speed. And, of course, much more... You can easily get this radiolocator device, which is controlled only by you at home.

An aerial radiolocator is a receiver for the mode-S/ADS-B beacon from a commercial transport aircraft, transmitted at a frequency of 1090MHz.

Integrated CPU/FPGA for signal processing applications

Integrated GPS receiver with 1PPS

SDR connects a broadband RF transmitter with CPU/FPGA processing to provide complete standalone software defined by radio solutions with unprecedented flexibility for a fraction of the size/weight/energy consumption of its competitors. In combination with a library ready to launch the application special software, Matchstiq ™ platform can be immediately used to deal with the demanding requirements for first day signal processing. As the user's requirements expand, other software applications are stored in a unit that provide a full set of features that can be selectively performed on the fly.

USRP E100 Kit, includes USRP E100, 2 RF Cables, Power Supply, and Hardware Package.

USRP E100 Kit, includes USRP E100, 2 RF Cables, Power Supply, and Hardware Package.

BladeRF X115 comes with a larger 115KLE Cyclone IV, FPGA, which provides additional space for hardware accelerators and signal processing chains involving FFTs,

Turbo decoders, transmit modulators/filters, and receive acquisition correlators for burst modems.

When unpacked from the bladeRF box, you can tune from 300MHz to 3.8GHz without the need for additional plates. Current open source drivers provide support for GNURadio among other things, allowing bladeRF to be placed for immediate use. This gives bladeRF the flexibility to act as its own RF modem, GSM and LTE cell, GPS receiver, ATSC transmitter or combination of Bluetooth/WiFi client's without the need for any expansion cards.