ANTENA 10W, SMA CONNECTOR 430MHZ / VNUT. Con.

This high linear preamplifier has been developed for use in the IFF (Identification Friend or Foe) frequency range at 1090 MHz. The preamplifier has a two-pole band pass between two amplifier stages for high suppression of out-of-band signals. This preamplifier is characterized by excellent high signal performance and low noise number.

PC interface USB cable for USC230/UBC3500XLT

USB cable-587 to PC PRO UNIDEN UBC3500 & USC230 SCANNERS

PC interface USB cable for USC230/UBC3500XLT

PC Cable to connect the scanner to the PC. The connection cable connects directly to the USB port to the computer and the USC-230E or UBC-3500XLT.

The SOFTWARE ARC3500 ,BUTEL software for UBC3500XLT is also on offer.

Frequency: 144 ~ 430MHz

- Frequency: 144 ~ 430MHz 

- Profit: 2,15 dB 

- Maximum power: 100WATTS 

- standing wave (VSWR): less 1,5 

- Impedance: 50 ohm 

- length: 210 mm 

- Connector type: SMA female

Frequency: 136 ~ 174 MHz / UHF: 400 ~ 470MHz

- Brand: Pryme 

- Color: black 

- Material: plastic + copper 

- frequency: VHF: 136 ~ 174 MHz / UHF: 400 ~ 470MHz 

- Profit: 3.2dBi / 5.6dBi 

- Maximum power: 10W 

- standing wave ratio (SWR): Less than 1.5 

- Impedance: 50 ohm 

- Length: 85 cm (max.), 28 cm (min.) 

- 2 sections 

- Connector type: SMA-male J 

- Suitable for Walkie Talkie Kenwood TH-G71A/TH-K2AT/K4AT, LT 61006200, 6288, 6600, 6100PLUS, 7700 (compatible with all SMA-J connectors)

Broadband mast pre-amp from 50 to 5000 MHz with excellent large signal rejection (IP3> 30dB) and low noise number, suitable for many applications: sensor, receiver or to increase the sensitivity of measuring instruments. Suitable also so low power amplifier with capacity up to 20 dBm output, amplification C. 20 dB, noise number c. 2 dB, N connectors, supply voltage 10 to 20V.

430MHz - 440MHz Vehicle magnetic antenna.

Frequency range 50 to 5000 MHz,

impedance of 50 ohms,

VF broadband amplifier 50 to 5000 MHz

Hard-packaging suitcases made of indestructible ABS material are stable and burdensome and offer optimal protection for your products.

Thanks to the special extrusion blowing technique, an air case between the inner and outer walls is created, ensuring even greater stability of the trunk against impacts.

This USB port The programming cable is used to program walkie-talkies from your computer.

USB programming cable, part of your picture - no sophomore ! Drivers on usb you will find was your software given, or WIN. 

This USB port The programming cable is used to program walkie-talkies from your computer.

Connected walkie talkie directly to the PC or laptop behind the USB port, without the need for an additional adapter / required option.

FIT FOR: GP88S

SIZE: 93 CM

GSM Directional Antenna

Directional Antenna / Sectorstrahler Monoband transmitting and receiving antenna for infrastruktur use Monoband Sende- und Empfangsantenne / Infrastruktur Polarization: Linear Radiation characteristics: Directional Gain: 10 dBi typ. VSWR: Ł 2 typ. Impedanz: 50 W Antenna typ: Patch-Resonator-Antenna max. power: 20 W HF-connection: N(f) connector

Alinco EDC36 12V car napajaci product for Alinco..

Alinco EDC36 Lighter Cable with Noise Filter

Lighter filter cable for all Alinco Handheld transceivery (except DJ-C6/C7 and DJ-S45/CJ-175 series). Also fits DJ-X3/X10/X2000 and V series.

DDS signal source, can be the use of DC power supply 5V sinusated output, rectangular (the operating cycle can be 1% -99% setting), 

This highly linear preamplifier has been developed for applications on the MFF frequency range (Identification Friend or foe) at 1090 MHz.

Low Noise Amplifier for SBS1

1070 ... 1100 MHz

This highly linear preamplifier has been developed for applications on the MFF frequency range (Identification Friend or foe) at 1090 MHz. This preamplifier is in a two-half band pass filter between two stages for amp high suppression out-of-band signals. This preamplifier excellent features great signal performance and low noise level figure.

Feature

High IP3 for excellent high signal performance

Low noise level image

ESD protection on the input preamplifier

Built-In distortion tee for remote power supply via coaxial cable

Built-In Band Pass Filter

The load range of the resistors termination is designed to provide an economic solution to the ever growing need for a compact, robust and easy end suitable for bench or filed use. Coaxial loads either to use a silent resistance chip or rod resistor depending on the desired power.

Black anodized aluminum alloy heat sinks are used for maximum thermal radiation with Type N connectors, however, additional connectors can be offered to meet the specific requirements of customers.

This series of endings are a medium power coaxial load that operates from DC to 2.5 GHz. Cooling ribs minimize temperature rise. The finishing element is enclosed in carefully enclosed coaxial housing. Standard connectors N and 7-16 DIN male or female.

These high performance directional couplings support internal/external applications in GSM, DCS and 3G bands up to 2500 MHz. Each steam unit defined the fraction of a powerful mobile signal with minimal reflections or losses. 

The wide frequency range allows use with multiband antennas, radiating cable systems, and wireless base stations. 

The dispositional loss was as small as possible and reliability strengthened. Each directional binding member comes with mounting hardware for easy wall mounting or mast.